Automotive Tools
ESSENTIALS FOR ANY GARAGE
When working on motors and general servicing it is vital that you have the right tools ready when you are. Whether it is a spark plug socket or hose clamps you need tools that are great to work with and bring better results.
-
Teng Tools Oil Filter Removal Strap Tool 160 mm Capacity 230 mm Handle - Car Tools for Filter Service - 9123 -
Teng Tools 4-Piece Pick Set — Straight Awl, 125-Degree Hook, 35-Degree Hook, Cotter Pin Puller in TT1 Tray - TTMDP -
Teng Tools 4-Piece Scraper Set — 22 mm Gasket Blade, Hook, Awl and Pin Puller in TT Tool Tray - TTSR04 -
Teng Tools 4 Piece Automotive Trim Tool & Panel Clip Remover Set - U-Shape & V-Shape Profiles - TT1 Tray - TTSR04A -
Teng Tools 5 Piece 1/2 Inch Wheel Tool Set — Breaker Bar, Impact Extension & Sockets in FOAMX4 Foam Tray - TEXW05 -
Teng Tools Brake Spring Washer Tool - Vehicle Brake Service and Maintenance Washer Removal and Installation - AT160 -
Teng Tools 90 mm Welding Magnets - Arrow Profile Magnetic Workpiece Holder for Fabrication and Tacking Work - MH90 -
Teng Tools Body Hammer Round Crown Face and Point Pin - Hickory Handle Auto Body Repair Dent Hammer 325 mm - HMBH02 -
Teng Tools 27 mm Fuel Injector Socket - 1/2 Drive Automotive Specialty Socket for Injector Removal & Service - AT360 -
Teng Tools 1/2 Inch Drive 7/8 Inch Heated Oxygen Sensor Socket - AT375 -
Teng Tools Magnetic PVC Fender Cover for Vehicle Paint Protection During Maintenance — 1070 mm x 400 mm - FC01 -
Teng Tools Hose Clamp Pliers - 57 mm Plastic Pinch Off Tool for Automotive Coolant and Fuel Hose Lines - AT090 -
Teng Tools Chain Pipe Wrench - Roller Chain Grip for Plumbing Wrench Tasks, Pipe Fittings and Round Stock - 9124 -
Teng Tools Body Working Hammer With Round Crowned Face and Flat Pein - Sheet Metal Tools for Auto Body Work - HMBH01 -
Teng Tools 1/2 Drive Torque Stick and Wheel Nut Impact Socket Set - 8 Pieces with DIN Adaptor in TT1 Tray - TTTS08 -
Teng Tools 3/8 Drive T-Bar Spark Plug Socket Set - 14 mm, 16 mm, 21 mm Sockets With Handle in FOAMX4 Tray - TEXTB05 -
Teng Tools File Needle Round Edge — TTNF12-12 -
Teng Tools File Needle Square — TTNF12-04 -
Teng Tools File Needle Barrette — TTNF12-08 -
Teng Tools File Needle Oval — TTNF12-10 -
Teng Tools File Needle Crossing — TTNF12-09 -
Teng Tools File Needle Three Square — TTNF12-03 -
Teng Tools 4 Piece Clip and Panel Removal Tool Kit - U-Shape & V-Shape Auto Trim Fastener Removers in FOAM1 Tray - TEASR04A -
Teng Tools 5-Piece Bodywork Hammer Set With Straight Pein, Point Pin, Square Milled and Two Dead Blow Heads in TT Tray - TTPSAD
Common questions
What counts as an auto tool here?
The tools you want ready when working on motors and general servicing — spark plug sockets, hose clamp tools, brake and engine service tools. The range exists so the right tool is there when you are.
Does the hose clip driver fit common clips?
It fits most commonly used worm-drive hose clips (Jubilee-type), and the flexible shaft reaches clips buried in confined engine bays.
Are the impact accessories standard-compliant?
Yes — for example the 1/2" double-ended impact socket set includes a 75mm impact extension bar made DIN on the female end and ANSI on the male end, so it works both ecosystems.
Why do spark plugs need a special socket?
Spark plug sockets are deeper than standard sockets and hold the plug captive — typically with a rubber insert or magnet — so you can lower the plug into a deep well and start it by hand without dropping or cross-threading it. Common plug hex sizes are 5/8" (16mm) and 13/16" (21mm); check your engine's spec.
Should I torque wheel and engine fasteners?
Yes — critical automotive fasteners (wheel lugs, head bolts, suspension components) have manufacturer-specified torque values, and both under- and over-tightening cause failures. Use a torque wrench set to the vehicle manufacturer's specification; see our Torque Equipment range.
Torque values and calibration guidance are from the Teng Tools catalogue. Always follow the fastener manufacturer's specified torque.