To remove an internal snap ring you need internal circlip pliers, the kind that close when you squeeze, with tips that fill the ring's lug holes. Take the load off the ring, seat the tips fully, squeeze only until the ring clears the bore, and lift it out pointing away from your face. Below are the five mistakes that make rings fly, then the right way in order.
TL;DR
- Internal rings come out with internal pliers, which close when you squeeze. External pliers open and only spread the ring tighter into its groove.
- Pick the plier by bore size and the tip by lug hole: about 1.5 mm on a 12 mm bore up to 3.5 mm on a 100 mm bore. Use the largest tip that goes fully in.
- Squeeze only until the ring clears the bore. Squeezing further bends it for good.
- Take the load off a stuck ring first, and never pry it out against the groove edge.
- Fit a new ring if the old one is bent, rounded edge toward the part, and check it is seated all the way round.
- Wear safety glasses. A ring that slips off a tip carries all the energy you put into it.
Table of Contents
- What you are taking out
- Mistake 1: the wrong type of plier
- Mistake 2: a tip that does not fit the lug hole
- Mistake 3: squeezing the ring past its limit
- Mistake 4: putting a bent ring back in
- Mistake 5: fitting it backwards or half seated
- How to remove an internal snap ring the right way
- What most circlip advice gets wrong
- Our perspective
- Pliers for internal and external circlips, 12 to 100 mm
- FAQ
- Sources
What you are taking out
An internal circlip, also sold as an internal snap ring, is a stamped spring steel ring in a groove inside a bore. It holds a bearing, seal carrier or gear against a thrust load. Metric rings follow DIN 472; the American standard for metric tapered section rings is ASME B27.7. Three things decide how it comes out:
- It is bigger than the bore. A DIN 472 ring for a 40 mm bore has a free diameter of 43.5 mm and sits in a 42.5 mm groove, per one ring maker's DIN 472 data sheet. To come out it must shrink below 40 mm.
- It has two lugs with holes for the plier tips. Spiral and wire rings with no lug holes come out with a pick instead.
- It stores energy. Every millimeter you squeeze is spring force waiting to be released.
Mistake 1: the wrong type of plier
Circlip pliers come in two actions that look alike on the bench:
- Internal pliers close when you squeeze. The tips pull the lugs together and the ring shrinks. Only this type takes a ring out of a bore.
- External pliers open when you squeeze. They spread a ring off a shaft.
- Straight or bent tips. Straight tips suit a ring you can see face on. Bent tips reach a ring deep in a bore or behind a shoulder.
Squeeze the handles in the air first. If the tips open, it is the wrong plier for a bore.
Mistake 2: a tip that does not fit the lug hole
A tip from the next range down tilts in the hole and walks out under load, which is when rings fly. A tip that is too big only touches the edge of the hole and slips. Use the largest tip that goes fully in. Lug holes grow with ring size; these figures are from a DIN 472 data sheet, set against common metric plier tips:
| Bore | Ring thickness | Lug hole | Common plier range and tip |
|---|---|---|---|
| 12 mm | 1.0 mm | 1.5 mm | 12 to 25 mm, 1.3 mm tip |
| 19 mm | 1.0 mm | 2.0 mm | 19 to 60 mm, 1.8 mm tip |
| 25 mm | 1.2 mm | 2.0 mm | 19 to 60 mm, 1.8 mm tip |
| 40 mm | 1.75 mm | 2.5 mm | 40 to 100 mm, 2.3 mm tip (move up) |
| 60 mm | 2.0 mm | 2.5 mm | 40 to 100 mm, 2.3 mm tip |
| 100 mm | 3.0 mm | 3.5 mm | 40 to 100 mm, 2.3 mm tip |
- One tip per range. Each range has a standard tip sized for every ring in it, such as 2.3 mm across 40 to 100 mm, so too small means a tip from a smaller range.
- Where ranges overlap, move up. A 1.3 mm tip sits loose in the 2.0 mm hole of a 25 mm ring. The 1.8 mm tip fills it.
Mistake 3: squeezing the ring past its limit
A ring is a spring only inside its elastic range. Squeeze an internal ring further than it needs and it takes a permanent set: it springs back smaller and no longer presses out into the groove. One ring maker's guide names this permanent set from over compressing, and for external rings has fitters set the plier stop against a pin gauge, wearing safety goggles.
- Squeeze only until the ring clears the bore. On a 40 mm bore that is just under 40 mm, not lugs touching.
- Do not squeeze and twist. Rolling a compressed ring out of its groove bends it out of flat.
Mistake 4: putting a bent ring back in
One ring maker says even its spiral rings, which are made to be removed, must be inspected before reuse and any damaged or deformed ring replaced. Many shops fit a new ring every time. If you do reuse one, check it:
- Flat. A ring that rocks on a flat surface is dished or twisted.
- Full size. If it drops into the bore with no squeeze, it has taken a set.
- Lugs intact. Cracks or stretched holes around the lugs are where it breaks.
- Not pried out. A ring levered out with a screwdriver is almost always bent.
Mistake 5: fitting it backwards or half seated
Stamping leaves one face of the ring with slightly rounded edges and the other with sharp ones. The common rule is to fit it with the sharp edge facing away from the retained part, so the square corner bears on the groove wall and resists camming out under thrust.
- Rounded edge toward the bearing or gear. Where a service manual gives a direction, the manual wins.
- Seat it all the way round. A ring standing proud at one point releases under load. A seated ring turns in its groove.
- Check the groove. One ring maker reports that groove deformation causes 90% of retaining ring failures, and a rounded groove corner lets a ring roll out.
A new ring in a damaged groove is still a failed ring.
How to remove an internal snap ring the right way
- Put on safety glasses. One snap ring patent notes the stored elastic energy of a deformed ring can make it fly and hit the person holding the pliers.
- Take the load off. If a bearing or spring pushes on the ring, press the part back toward its seat.
- Clean the lug holes and groove of dirt, rust and old grease.
- Turn the lugs where you can reach them, if the ring will rotate.
- Choose the plier: internal action, the range for the bore, the largest tip that fills the hole, bent tips if the ring sits deep.
- Seat both tips fully, square to the ring face.
- Squeeze slowly until the ring just clears the bore wall. Stop there.
- Lift it straight out, pointing away from you and anyone nearby. A rag over the bore catches a ring that lets go.
- Inspect the ring and the groove before anything goes back in.
What most circlip advice gets wrong
The common shortcut for a stuck internal ring is to skip the pliers. The general reference notes that in the field needle nose pliers or a flat screwdriver used as a lever are sometimes swapped in, and one mechanics' forum thread runs to seal picks, screwdrivers and drilling an access hole, with warnings that picks break and rings fly.
- The lever rests on the groove edge, the edge that carries the thrust load.
- A pried ring is a scrap ring. The shortcut ends with a new ring anyway.
- Picks have a place: spiral and wire rings with no lug holes. A ring with lug holes is made for pliers.
Our perspective
Most circlip trouble is a sizing problem dressed up as a stuck ring. One plier that nearly fits means a tip half in the hole, a squeeze that goes too far, and a ring that flies or comes out bent. So we built the kit around the whole range: three ranges, both actions, straight and bent, so the tip that fits is already on the bench.
If you are choosing between two tips, take the bigger one that still goes all the way into the hole.
Pliers for internal and external circlips, 12 to 100 mm
The Teng Tools Bearing and Gear Circlip Plier Kit is 12 pieces in three tray sets, each with internal straight, internal bent, external straight and external bent pliers, made to DIN 5254 and DIN 5256:
- 12 to 25 mm set (TT474-5) with 1.3 mm tips, on a TT1 tray. Pliers 125 to 145 mm long for small shafts and bores.
- 19 to 60 mm PRO set (TT474-7E) with 1.8 mm bearing steel tips and an invisible return spring. Pliers 165 to 175 mm long for most bearing and gear work.
- 40 to 100 mm set (TTX474-9) with 2.3 mm tips, in a TTX4 tray. Pliers 225 to 250 mm long for large gearbox shafts and housings.
The ranges overlap at 19 to 25 mm and 40 to 60 mm, so a ring near a boundary gets the tip that fills its hole. Retaining rings are not included; rings above 100 mm are outside the kit.
Browse the millwright tool kits for other bearing and gear jobs, or the full plier range for single pliers.
FAQ
Which pliers remove an internal snap ring?
Internal circlip pliers. Their tips close when you squeeze, pulling the two lugs together so the ring shrinks out of the bore groove. External pliers open when you squeeze, so they cannot take an internal ring out.
What size circlip pliers do I need for an internal ring?
Match the plier to the bore size and the tip to the lug hole. Common metric ranges are 12 to 25 mm with a 1.3 mm tip, 19 to 60 mm with a 1.8 mm tip and 40 to 100 mm with a 2.3 mm tip. Use the largest tip that fully enters the hole.
How do you remove a stuck internal circlip?
Push the bearing or part it holds back toward its seat to take the load off, and clean the lug holes and groove. Seat the tips fully, squeeze only until the ring clears the bore, and lift it out pointing away from you.
Can you reuse an internal circlip?
Only if it comes out flat, round and undamaged, and many shops replace it every time. A ring that was squeezed too far, twisted or pried out has lost its grip on the groove. Scrap it.
Which way round does an internal circlip go?
A stamped ring has one rounded edge and one sharp edge. Fit the rounded edge toward the part it holds and the sharp edge away, so the square corner bears on the groove wall. Where a service manual gives a direction, follow it.
Sources
- DIN 472 Internal Circlips Type J, Catalogue Data Sheet, JC Fasteners
- B27.7 General Purpose Tapered and Reduced Cross Section Retaining Rings (Metric), ASME
- The Ultimate Retaining Ring Guide, Rotor Clip
- #1 Reason for Retaining Ring Failure and How to Overcome It, Smalley
- Ask the Expert: Retaining Ring Reusability, Smalley
- Internal Retaining Rings, Albany County Fasteners
- Circlip, Wikipedia
- US9156150B2, Snap Ring Pliers, Google Patents
- How to Remove an Internal Retaining Ring, The Garage Journal forum
